Skip to content

Free C-6: Cabinets practice test

  • 15 questions
  • ~8 minutes
  • Scored instantly

15 questions from the Peerless Institute C-6: Cabinets exam, including five questions about one diagram. The C-6: Cabinets exam covers the following topics:

  • Planning and Estimating20%
  • Cabinetry and Millwork Fabrication24%
  • Cabinet Installation25%
  • Millwork Installation16%
  • Worker and Job Site Safety15%

Percentages are approximate, per the CSLB examination content outline.

Study materials for this exam

0 of 15 answered
  1. 1The warp for any 1-3/4 inch thick standard door shall not be more than ______

  2. 2If excavating a trench 25 meters x 14 meters x 5 ft., how many cu. yds. are there?(NOTE: There are 3.218 ft. in one meter. The answer is arrived at by the following equation:(25 x 3.218) x (14 x 3.218) x 5 divided by 27 = 697.7 = 672 cu. yds.)

  3. 3The finished thickness of 1-1/2 inch nominal rough lumber, with the exception of redwood, is:

  4. 4A reinforcing strip is not required, if material at least ______ thick is used as a drawer bottom, according to WIC standards.

  5. 5Metal ladders should be at least ___ feet from 220 volt electrical wiring.

  6. 6Most hardwoods are not recommended for exterior use. The common exceptions are:

  7. 7If you have a 16" wide opening which is 24" high and are to install drawers using guides which require 1/2 inch clearance on each side of the drawer, how wide should you make the drawer?

  8. 8Generally, when not specifically stated by the code, nails or spikes shall have a required penetration of not less than ____ diameters.

  9. 9Tom, the stair contractor, was to calculate the rise and number of treads on a set of stairs which had a total rise of 10 feet. He converted the total rise to inches, divided the height by 7 and then divided 120 with his answer and then added 1. He now had the height of the individual rise and the proper number of treads.

  10. 10When pneumatic nailers and staplers are in use, all personnel, except tool operators, may not come within how many feet of the area?

Diagram practice

Use this diagram to answer the next five questions. Use the stated exercise data; the drawing is not to scale.

A36-by 30 inch face frame has 2 inch stiles and 2.5 inch rails. The open center is drawn separately from the frame.
Inset door and face-frame dimension chain · Open full-size diagram in a new tab
Diagram text description

A36-by 30 inch face frame has 2 inch stiles and 2.5 inch rails. The open center is drawn separately from the frame. PEERLESS / CABINET, MILLWORK & FINISH CARPENTRY C06-DX-01 Inset door and face-frame dimension chain 36 in overall 30 in 2 in stile Rail: 2.5 in PROJECT DETAIL Inset door:1/8 in clearance at each edge. Detail rails:2.5 in. Conflicting schedule rails:3 in. Finished inset door height:24.75 in. Hold fabrication until the rail discrepancy is reconciled. Diagram interpretation exercise • Not a construction document • Not to scale A rectangular face frame has vertical stiles and horizontal top/bottom rails surrounding an open center. No door leaf is drawn in that center.

  1. 11What is the clear opening width?

  2. 12What finished inset-door width leaves the specified clearance on both sides?

  3. 13If the schedule’s 3 inch top and bottom rails replace the drawn 2.5 inch rails, does the 24.75 inch-high door still fit the 30 inch overall frame?

  4. 14Using the detail’s 2.5-in top and bottom rails, what is the clear opening height?

  5. 15Using the detail’s 2.5-in rails and the 24.75-in door, what is the combined top-and-bottom clearance?